WWW | Strona główna forum | Rejestracja | Garaż | FAQ | Społeczność FKP | Galeria FKP | Kalendarz | Dzisiejsze posty | Szukaj |
Foczka miesiąca |
|
Elektryka, audio i alarmy Wszystko co elektryczne. |
|
Narzędzia wątku | Wygląd |
27-01-11, 21:14 | #8 |
Sympatyk
Grupa: Małopolska
Zarejestrowany: Jan 2006
Skąd: Kraków
Inny
HB 5D
2.0 DuraTorq 136KM manual
lipiec
2013
Postów: 917
|
dzisiaj wyrzucił mi jeszcze błąd :
B1600 9600 PATS Ignition Key Transponder Signal is Not Received - Damaged Key or Non -PATS Key Może uda mi się dojechać do mechanika. wg google trzeba wykonać taką procedurę B1600-1 ON DEMAND SELF TEST Record continuous stored DTCs. Erase DTCs and perform on-demand self test as described in Section 18-04 . Is DTC B1681 present? Yes No GO to DTC B1681 . GO to B1600-2 . B1600-2 CHECK TRANSCEIVER MOUNTING Gain access to transceiver as described. Check transceiver module for proper mounting. Is module mounted correctly? Yes No GO to B1600-3 . RELOCATE and SECURE module to proper position. CLEAR DTCs and RERUN self test to verify no DTCs. B1600-3 CHECK TRANSCEIVER MODULE CONNECTIONS Enter NGS: PATS, Active Command Modes. Perform Transmit Signal Command ON. NOTE: The transmit signal produces a 2 second ON, 2 second OFF cycling of voltages. Disconnect transceiver module connector C241 and probe harness connector. Using a voltmeter, check RF Circuit 164 (P/L for voltage between transceiver module connector C241 and known good ground. Is voltage above 8 volts? Yes No GO to B1600-4 . SERVICE Circuit 164 (P/L for open or short circuit. CHECK fuse 18 (15A) for open. RESTORE vehicle. RETEST system. B1600-4 CHECK RF GROUND CIRCUIT Repeat Transmit Signal Command ON. Using an ohmmeter, check Circuit 165 (T/W) between transceiver module connector, C241 and known good ground. Is resistance less than 5 ohms? Yes No GO to B1600-5 . SERVICE Circuit 165 (T/W) for open. RESTORE vehicle. RETEST system. B1600-5 CHECK TX SIGNAL Repeat Transmit Signal Command ON. Using a voltmeter, check Circuit 167 (BR/O) between TX signal on transceiver module connector C241 and known good ground. Is voltage above 2 volts? Yes No GO to B1600-6 . SERVICE for open or short on Circuit 167 (BR/O). CHECK connector for open or loose pins. RESTORE vehicle. RETEST system. B1600-6 CHECK RX SIGNAL Repeat transmit signal command on. Reconnect module connector. Using a voltmeter connected to a known good ground, back probe Pin 3 of the transceiver module harness connector C241 . Is voltage above 2 volts? Yes No GO to B1600-7 . SERVICE for open or short on Circuit 168 (R/BK). CHECK connector for open or loose pins. RESTORE vehicle. RETEST system. B1600-7 CHECK WITH NEW ENCODE ID KEY Enter NGS: PATS, Active Command Mode. Select ignition key-code erase ON as described. Erase ignition keycode as described under Service Procedures, Key Initialization . (Wait minimum of 8 minutes.) Cycle ignition switch from OFF to RUN to program new key. Turn ignition switch to START position. Did engine start? Yes No System operating properly. RESTORE vehicle. (Use Spare Key Programming procedure as described under Service Procedures to program additional keys.) REPLACE transceiver module. RESTORE vehicle. GO to B1600-8 . B1600-8 CHECK TRANSCEIVER MODULE Cycle ignition switch from OFF to RUN to program new key. Turn ignition switch to START position. Did engine start? Yes No System operating properly. RESTORE vehicle. (Use Spare Key Programming procedure as described under Service Procedures to program additional keys.) REPLACE passive anti-theft system control module. RESTORE vehicle. GO to B1600-9 . B1600-9 CHECK ANTI-THEFT MODULE Cycle ignition switch from OFF to RUN to program new key. Turn ignition switch to START position. Did engine start? Yes No System operating properly. RESTORE vehicle. RETEST system. REFER to Powertrain Control/Emissions Diagnosis Manual to diagnose powertrain control module. Wygląda na to, że uszkodził się kluczyk samochodowy
__________________
Czas na zmiany .... tutaj była fajna ikonka, ale znikła ... snowboard ... moja nowa zajawka Ostatnio edytowane przez rayos ; 27-01-11 o 21:17 |
Tagi |
dtc 9600, immobilizer, uszkodzony kluczyk |
|
|
Podobne wątki | ||||
Temat | Autor wątku | Forum | Odpowiedzi | Ostatni post / autor |
[MK1] Wymiana stacyjki a immobilizer. Zablokowana kierownica. | KamilK | Elektryka, audio i alarmy | 13 | 09-11-14 09:41 |
[FFII] Zapasowy klucz do Focusa II, immobilizer, kodowanie. | grjakub | Inne techniczne | 7 | 09-02-12 21:54 |
Dorobienie kluczyka - zaprogramowanie immobilizer | Crit3r | Elektryka, audio i alarmy | 77 | 03-10-11 16:16 |
immobilizer nie dział | obuch-zg | Elektryka, audio i alarmy | 2 | 16-09-09 08:35 |
[FFI] Alarm cobry wariuje | thermalfake | Elektryka, audio i alarmy | 10 | 28-10-08 20:27 |
Kontakt - |